Найдено научных статей и публикаций: 5, для научной тематики: Компресор
1.
В.А. Коваль, Е.А. Ковалева
- Східно-Європейський журнал передових технологій , 2012
На підставі варіаційного принципу максимуму потоку механічної енергії за допомогою методу малих обурень розроблен критерій переходу осьового компресорного рівня до режимів обертового зриву з врахуванням особливостей формування профільного і торцевого примежевих шарів....
На підставі варіаційного принципу максимуму потоку механічної енергії за допомогою методу малих обурень розроблен критерій переходу осьового компресорного рівня до режимів обертового зриву з врахуванням особливостей формування профільного і торцевого примежевих шарів.
В.А. Коваль, Е.А. Ковалева Прогнозирование режимов вращающегося срыва в ступени осевого компрессора с учетом формирования профильного и торцевого пограничных слоев // Східно-Європейський журнал передових технологій, Vol. 3, Issue 3, 2012, pp. 4-8
2.
В.Е. Беляев, С.О. Беляева, И.В. Трофимович
- Східно-Європейський журнал передових технологій , 2012
Наведено інформацію щодо розробленої на підприємстві ФДУП «ММПП «Салют» газотурбінних установок малої розмірності для застосування їх на різних об’єктах у якості джерела з виробництва електроенергії й тепла. Проведений порівняльний аналіз із закордонними зразками....
Наведено інформацію щодо розробленої на підприємстві ФДУП «ММПП «Салют» газотурбінних установок малої розмірності для застосування їх на різних об’єктах у якості джерела з виробництва електроенергії й тепла. Проведений порівняльний аналіз із закордонними зразками.
В.Е. Беляев, С.О. Беляева, И.В. Трофимович Применение малоразмерных ГТУ в системах децентрализованного энергоснабжения // Східно-Європейський журнал передових технологій, Vol. 3, Issue 2, 2012, pp. 59-61
3.
В.А. Коваль, Е.А. Ковалева
- Східно-Європейський журнал передових технологій , 2012
The engineering method of calculation of wall boundary layer in the axial-flow compressor, developed on the basis of the physical model of the flow gained as a result of numerical experiment by means of earlier tested on various plants 3-D of complex ANSYS CFX is reduced. The gained model allows...
The engineering method of calculation of wall boundary layer in the axial-flow compressor, developed on the basis of the physical model of the flow gained as a result of numerical experiment by means of earlier tested on various plants 3-D of complex ANSYS CFX is reduced. The gained model allows to determine integral performances of wall flows on various operational modes, including and the conditions, previous a rotating stall.
В.А. Коваль, Е.А. Ковалева Modeling of a face interface in a step of the axial compressor // Східно-Європейський журнал передових технологій, Vol. 3, Issue 2, 2012, pp. 20-24
4.
Ю.М. Ануров, Д.Г. Федорченко
- Східно-Європейський журнал передових технологій , 2012
Habits of maintenance of strength reliability of aero-engines by protection against run-up of a rotor and maintenance of damage containing ability of bodies are observe. Results of tests and calculations of designs of a turbine engine of family NK, and also a design of some units are resulted....
Habits of maintenance of strength reliability of aero-engines by protection against run-up of a rotor and maintenance of damage containing ability of bodies are observe. Results of tests and calculations of designs of a turbine engine of family NK, and also a design of some units are resulted.
Ю.М. Ануров, Д.Г. Федорченко Maintenance of constructional reliability aviation GTE families "NK" by protection against promotion of a rotor and the cases, which impenetrable // Східно-Європейський журнал передових технологій, Vol. 3, Issue 2, 2012, pp. 8-10
5.
В.В. Романов, В.А. Коваль
- Східно-Європейський журнал передових технологій , 2012
Habits of application of various alloys for the basic units and details stationary GTE, formed on the basis of ship are observed. Results of the comparative analysis of designs of compressors of low and tall pressures GTE DN80, and also the data describing of strength properties of serial materi...
Habits of application of various alloys for the basic units and details stationary GTE, formed on the basis of ship are observed. Results of the comparative analysis of designs of compressors of low and tall pressures GTE DN80, and also the data describing of strength properties of serial materials are resulted. Last achievements in the field of creation of hightemperature alloys aviation GTE are shown.
В.В. Романов, В.А. Коваль Application of new materials at converting ship and aviation gas-turbine engines GTE in stationary gas-turbine installations GTI // Східно-Європейський журнал передових технологій, Vol. 3, Issue 2, 2012, pp. 4-7